Modine PDP200AE0130 200,000 BTU Vertical Powered Vented Unit Heater - 115V - NG

Sku:
MODINE-PDP200AE0130
Usually Leaves Warehouse in 2 - 3 Business Days
$2,239.00
Featuring 82% thermal efficiency, this unit heater is 115 volts and has 200,000 BTUs input / 164,000 BTUs output. The Modine PDP150AE0130 power vented heater can be added to many commercial locations. The Modine Vertical Powered unit can be used vertically or horizontally and the exhaust can be rotated a full 180°. These units are designed to use the smallest diameter vent pipe possible. The intermittent pilot-ignition system features 100% shut-off and continuous retry and auto restart. If needed, the unit can be field converted from natural gas to liquid propane with a conversion kit (available above).
  • Ignition controller: The system will attempt to light 3 times (every 6 minutes) before lockout and re-attempt ignition after about an hour. This will continue indefinitely until the pilot flame is sensed or power is interrupted to the system
  • Time Delay Relay: The time delay relay allows the gas controls to operate for approximately 30 to 90 seconds before the blower starts, so that the initial delivered air is not cool. The time delay relay also keeps the motor running for approximately 30 - 90 seconds after the call for heat has been satisfied to remove the residual heat from the heat exchanger
  • Control Step Down Transformer
  • Pressure Switch: A automatic reset vent pressure switch is supplied on all power vented unit heaters to prevent operation of the main burner in the event there is restricted venting of flue products.
  • Power Exhauster: The power exhauster may be rotated 180° to allow for various venting directions

The Modine PDP200AE0130 is Natural Gas but can be converted for use with Liquid Propane with an LP conversion kit (28050, sold separately above) to meet your installation needs.

FREE SHIPPING ON ALL ORDERS!
Modine PDP200 200,000 BTU Vertical Powered Vented Unit Heater, 115V

Product Overview

Featuring 82% thermal efficiency, this unit heater is 115 volts and has 200,000 BTUs input / 164,000 BTUs output. The Modine PDP150AE0130 power vented heater can be added to many commercial locations. The Modine Vertical Powered unit can be used vertically or horizontally and the exhaust can be rotated a full 180°. These units are designed to use the smallest diameter vent pipe possible. The intermittent pilot-ignition system features 100% shut-off and continuous retry and auto restart. If needed, the unit can be field converted from natural gas to liquid propane with a conversion kit (available above).
  • Ignition controller: The system will attempt to light 3 times (every 6 minutes) before lockout and re-attempt ignition after about an hour. This will continue indefinitely until the pilot flame is sensed or power is interrupted to the system
  • Time Delay Relay: The time delay relay allows the gas controls to operate for approximately 30 to 90 seconds before the blower starts, so that the initial delivered air is not cool. The time delay relay also keeps the motor running for approximately 30 - 90 seconds after the call for heat has been satisfied to remove the residual heat from the heat exchanger
  • Control Step Down Transformer
  • Pressure Switch: A automatic reset vent pressure switch is supplied on all power vented unit heaters to prevent operation of the main burner in the event there is restricted venting of flue products.
  • Power Exhauster: The power exhauster may be rotated 180° to allow for various venting directions

The Modine PDP200AE0130 is Natural Gas but can be converted for use with Liquid Propane with an LP conversion kit (28050, sold separately above) to meet your installation needs.

Tech Specs

General Features

Installation Type:
Ceiling Mount
Fuel Type:
Natural Gas (NG)
Certified Usage:
Commercial (Indoor Only)
Separated Combustion Chamber:
No

Performance

Heating BTUs (Input):
200000
Heating BTUs (Output):
166000

System Data

Noise Level (dBA):
NA
Thermal Efficiency:
82%
CFMs:
2870
Output Velocity (FPMs):
819
Discharge Air Temperature Rise (°F):
52
Discharge Air Opening Area (ft²):
NA

Connections

Gas Connection Size:
1/2"
Vent Connection Size (in.):
5"

Clearances

Top to Ceiling (in.):
5"
Bottom to Floor (ft.):
1'
To Side Wall (in.):
1"
Access Panel (in.):
18"
Flue / Vent Connector (in.):
7"

Weights and Dimensions

Width (in.):
25.625
Depth (in.):
25
Height (in.):
40.25
Net Weight (lbs.):
239

Electrical Requirements

Voltage:
110-120V
Amps:
5.15
Circuit Breaker Size (Amps):
15
California residents see Prop 65 WARNINGS

Warning WARNING!

Warning: Cancer and Reproductive Harm - www.p65warnings.ca.gov

Product Warranty

Heat Exchanger: 10 Years